If you mean 12-gauge high-brass shotgun ammunition, none of the products listed here is ammunition. They are brass wire, brass sheet, or a plumbing trap. For craft and fabrication projects, the two red brass wires are better suited to bending and jewelry work, while the brass sheet is intended for flat-piece projects. Check the product descriptions carefully: “12 gauge” describes material thickness here, not a shotgun shell.
| Product | Best suited for | Important distinction |
|---|---|---|
| CRAFT WIRE CDA #260 Red Brass Wire | Crafts needing a longer wire length | Dead-soft 12-gauge wire |
| Craft Wire CDA #230 Red Brass Wire | Small wire projects | Three-foot length |
| Tynulox H62 Brass Sheets | Flat craft and repair pieces | Two 2 mm sheets |
| uxcell Brass Craft Wire | Flexible craft and jewelry work | About 9.8 feet of H65 brass |
| Westbrass P-Trap | Sink plumbing installations | Not craft wire or a sheet |
CRAFT WIRE CDA #260 Red Brass Wire
This round, dead-soft wire is listed as 12 gauge and comes in a one-pound coil measuring approximately 54 feet. It is the best choice in this group for a project that needs substantially more wire than a short jewelry or prototype piece.
Best for: Makers who need a long supply of soft red brass wire for forming or craft work. The listed dead-soft hardness makes it a more suitable choice for bending than a rigid brass sheet.
Check before buying: The product name identifies CDA #260, but the feature text says CDA #230. Confirm the alloy specification with the seller if the exact composition matters. This is craft wire, not shotgun ammunition.
Craft Wire CDA #230 Red Brass Wire
This 12-gauge, round wire is described as dead soft and made from CDA #230 red brass, with 85% copper and 15% zinc. The listed amount is one ounce, or about three feet, making it a smaller-quantity alternative to the longer coil.
Best for: Small projects, samples, and makers who want a short length of a specified red brass alloy. Choose this if you do not need a 54-foot supply.
Limitation: The short length may not suit larger designs or projects requiring repeated pieces. The listing describes craft material, not a high-brass shotshell.
Tynulox H62 Brass Sheets
This listing includes two H62 brass plates, each described as 2 mm thick and 100 by 100 mm (about 3.9 by 3.9 inches). The seller notes heat-transfer capability and electrical conductivity. Unlike the wire products, these are flat stock pieces for projects that call for sheet material.
Best for: Model making, crafts, and small repair tasks where a compact brass plate is more useful than bendable wire.
Limitation: The material is sheet stock, not a flexible wire or ammunition component. Verify the dimensions and alloy designation against your project requirements before ordering.
uxcell 12-Gauge Brass Craft Wire
The listing describes approximately 9.8 feet of soft, non-insulated H65 brass wire at 12 gauge, or about 2 mm thick. It is presented for jewelry making, crafts, modeling, electroplating, and decoration. Its length falls between the three-foot and 54-foot wire options in this list.
Best for: Buyers wanting a moderate length of soft wire for bending into designs without needing a large coil.
Limitation: It is craft wire, and the listing does not identify it as shotgun-shell brass. Do not select it based on an ammunition interpretation of “12 ga.”
Westbrass Brass P-Trap Kit
This is a 1-1/4-inch brass P-trap kit with a high box flange, not 12-gauge brass material. The listing gives an approximate measurement of 11-1/2 inches from the trap-neck center to the end of the tailpiece.
Best for: A buyer specifically looking for a sink P-trap with a finished flange. It is included because it is the only plumbing product in the supplied list, not because it matches “12 ga high brass.”
Limitation: Avoid this item for wire, sheet-metal, jewelry, or ammunition needs. Confirm plumbing measurements and installation requirements before purchase.
Buying Guide
Does “12 ga high brass” mean shotgun ammunition?
It can refer to 12-gauge shotgun shells with high-brass construction. None of the supplied listings is a shotshell. These products use gauge as a wire or material-thickness description, or refer to plumbing dimensions. If you need ammunition, look for a listing that explicitly identifies 12-gauge shotshells and the required load details.
Which brass wire should you choose?
Compare the listed length and alloy. The CRAFT WIRE coil offers the most wire, while the CDA #230 option is a shorter three-foot amount. uxcell supplies about 9.8 feet of H65 wire. If alloy composition is important, confirm the details, especially where the listing name and features do not agree.
When is brass sheet a better fit than wire?
Choose sheet stock when a project needs a flat plate or panel. Choose wire when the design calls for a line that can be bent or wrapped. Check thickness, width, length, and material composition before ordering.
Frequently Asked Questions
Are these products high-brass 12-gauge shotgun shells?
No. The supplied products are craft wire, brass sheet, and a plumbing P-trap. None is listed as ammunition.
What does 12 gauge mean for the wire listings?
The listings use 12 gauge to describe wire size, with one listing also giving an approximate 2 mm thickness. It does not mean a 12-gauge shotgun shell.
Which listed wire has the longest length?
The CRAFT WIRE one-pound coil is listed as approximately 54 feet, longer than the 9.8-foot uxcell wire and three-foot CDA #230 wire.
Can the Westbrass product be used for a craft project?
It is described as a brass P-trap kit for plumbing. It is not presented as craft stock, wire, or ammunition, so select it only for a matching plumbing need.